FAQ's

 

The Plate
Required in all countries.
Aluminum label plate, ready to be engraved, for mounting on the frame of your bike.
The manufacturer does not supply unengraved frame label plates, and until now it was impossible to find them.

The Product
Alu Labels PLATE to apply on the frame of your bike.
Required In all countries , ready to be written on.
Anodized aluminium, easy to bend and adapt to each type of frame. 

Engravement 

 Do not attempt to engrave the data by hand, it will not be acceptable to the authorities.
Any Trophy Shop or Jeweler, and most gunsmiths, will engrave the data for you at a very low cost.
 
 

Is a frame label plate required? 
Yes. It is required for any motorcycle that is licensed/registered in almost every state in Europe, the USA, and Australia. 

Is it legal to temporarily remove it from the frame? 
Yes, you can remove and replace it. For example, if you have to repair or repaint the frame. 

Is it illegal to buy and engrave a label? 
No. It is, however, illegal to engrave a plate with incorrect or false information. If you are unsure about your circumstances, consult an expert.

What should be listed on the label? 
The Serial Number of the motorcycle (called V.I.N. in the USA). The brand name of the manufacturer and the model of the bike are required. In some countries or states in the USA the engine serial number is required. The year of manufacture and the maximum gross weight (the weight of the bike plus the maximum allowable weight of passengers and other items) are also required. If you are unsure which items are required in your country or state, ask your mechanic (even a car mechanic), he will know. The information on the plate must be clear and legible. 
 

Conseils pour plier correctement la plaque d'identification
Tips for bending correctly the VIN plate
Consiglio di come piegare una vin plate
  

1. Size

Mesurez le diamètre du cadre où vous voulez appliquer la plaque d'identification Measure the diameter of the frame where you want to apply the VIN PLATE Misurare il diametro del telaio dove si vuole applicare la VIN PLATE

 
 

2. Find

Cherchez un tube d'un diamètre intérieur avec peu de différence + /- (1, 2 mm) Look for a tube with internal diameter with little difference + / - (1, 2 mm) Cercare un tubo con diametro interno uguale o con poca differenza + / - (1, 2 mm)

 
 

3. Cut

Coupez le tube à la longueur désirée (120 mm conseillé) Cut the tube to the desired length (120 mm recommended) Tagliare il tubo alla lunghezza voluta (120 mm consigliato)

 
 

4. Cut

Couper sur  la longueur afin d'avoir deux moitiés. Si vous n'êtes pas sûr, couper un peu moins pour mieux finir une partie. Cut the length so you have two halves. If you are not sure cut a little less so to finish better than one half.  Tagliare sulla lunghezza in modo da avere due metà. Se non siete sicuri tagliate un po' meno in modo da rifinire meglio una metà

 
 

5. Finish

Enlevez les bavures et polir les bords correctement, éliminant les angles vifs. Remove burrs and polish the edges properly, eliminating sharp corners. Togliere le bave e rifinire correttamente i bordi, eliminare angoli taglienti.

 
 

6. Stand

Fixez un soutien à la base Fix a support at the bottom Fissare un supporto nella parte inferiore

 
 

7. Pipe Smaller

Cherchez un morceau de tuyau de diamètre inférieur. Looking for a piece of pipe, diameter smaller. Cercare un pezzetto di tubo di diametro inferiore.

 
 

8.Adhesive

Couvrez avec de l'adhésif à l'intérieur du tube pour protéger la plaque  des rayures. Cover with adhesive to the inside of the tube to protect the VIN PLATE from scratches Ricoprire con adesivo la parte interna del tubo per proteggere la VIN PLATE da graffi.

 
 
 

9. END

Maintenant vous pouvez plier la plaque de la façon dont vous voulez  Now you can bend the plate the way you want Ora potete modellare come desiderate la vostra VIN PLATE

 
Ces instructions simples peuvent ètre trouvées résumées dans un petit film sur:
These simple instructions can be found summarized in a short film on:
Queste semplici istruzioni li trovate riassunte in un piccolo filmato su:


Find in a click